All Collections
Troubleshooting
How to Power-Cycle Your Tracker
How to Power-Cycle Your Tracker

A Step-by-Step Guide to Refreshing Your Tracker's Performance

Mitch Logistimatics avatar
Written by Mitch Logistimatics
Updated over a week ago

Power cycling your tracker is a simple yet effective troubleshooting technique that can help resolve various issues. It involves turning off and then turning on your tracker device to refresh its system and establish a stable connection. By power cycling, you can address unresponsiveness, connectivity problems, and other common glitches. It serves as a quick and convenient solution to get your tracker back on track and functioning optimally.


TRACKER LIST

MOBILE 200 4G GPS TRACKER

  1. Power ON the tracker: Locate the power button on the Mobile 200g tracker. Press and hold the power button for 3-4 seconds, then release. You will notice that all three lights on the tracker flash briefly, indicating that the device is powered on.

  2. Power OFF the tracker: To power off the Mobile 200g tracker, press and hold the power button for a slightly longer duration, around 5-6 seconds, then release. During this time, you will observe that the lights on the tracker flash continuously. Once the lights suddenly stop flashing, it means that the tracker has powered off successfully.

  3. Check the power status: If you are unsure whether the tracker is powered on or off, you can quickly check. Simply tap the power button once and release it. Observe the lights on the tracker. If the lights flash, it indicates that the tracker is powered on. If no lights flash, it means that the tracker is powered off.

By following these step-by-step instructions, you can effectively power cycle the Mobile 200g tracker. This process helps to reset the device and resolve any potential issues. If you encounter any difficulties or require further assistance, please refer to the device's user manual or contact our support team for additional guidance.

CAR CHARGER 4G GPS TRACKER

  1. Uninstall the device from the vehicle: Begin by removing the car charger tracker from its current location in your vehicle. Follow the manufacturer's instructions or refer to the user manual for proper uninstallation steps.

  2. Reinstall the device: Once the device has been removed, reinstall it back into the vehicle. Ensure that it is securely connected and in the correct position as specified by the manufacturer.

  3. Start the vehicle's engine: To ensure that the device receives sufficient power, start your vehicle's engine. This will provide the necessary power source for the tracker to function properly.

  4. Take the vehicle for a ride: Now that the device is reinstalled and the engine is running, take the vehicle for a ride. Drive for a reasonable distance to allow the tracker to establish a stable connection and gather accurate location data.

By following these steps, you will effectively power cycle your car charger tracker, allowing it to reset and establish a proper connection. If you encounter any issues or require further assistance, please consult the device's user manual or reach out to our support team for additional guidance.

ROAD-WIRED TRACKER

  1. Locate the power switch: Find the power switch located beside the SIM card slot on the device.

  2. Power On: To turn on the device, toggle the power switch to the "On" position. You should see indicator lights or an LED display indicating that the device is powered on.

  3. Power Off: To turn off the device, toggle the power switch to the "Off" position. The indicator lights or LED display should turn off, indicating that the device is now powered off.

  4. Wait for a few seconds: After turning off the device, wait for about 10 seconds before proceeding to the next step.

  5. Power On again: Toggle the power switch back to the "On" position to power the device once more. The indicator lights or LED display should light up again, indicating that the device has been successfully power-cycled.

By following these steps, you can effectively power-cycle your RoadWired tracker. Power cycling can help resolve certain issues and ensure the device is functioning properly.

MICRO-431 POCKET TRACKER

To Power Off:

  1. Locate the function key on the Pocket Tracker. It is usually labeled or indicated by an icon.

  2. Press and hold the function key for approximately 3 seconds. Keep holding it until the red battery light becomes solid.

  3. Wait for 60 seconds while the device remains in this state. You may notice vibration and the lights turning off completely. This indicates that the device is now powered off and successfully reset.

To Power On:

  1. To power on the Pocket Tracker, locate the power button or the designated button for turning it on.

  2. Press and hold the button for 3 seconds. You will see all four LEDs illuminate and feel a vibration from the device. This signifies that it has been successfully powered on.

By following these steps, you can effectively power-cycle your Pocket Tracker. Power cycling can help resolve certain issues and ensure the device is functioning properly.

PROTECT PLUS

  1. Locate the front plate of the device. You will notice a rubbery gasket covering the area where the power switch and SIM card are located. It's essential to keep this gasket in place to maintain water resistance. If you need to access the power switch, carefully remove the gasket, ensuring that you reinstall it securely afterward.

  2. To power off the device, you need to remove the front plate and the rubber gasket. Carefully detach the front plate, taking care not to damage any components. Once the front plate is removed, locate the power switch beneath it.

  3. Toggle the power switch to the OFF position. This will effectively power off the device. Remember to reassemble the front plate and securely reinstall the rubber gasket to maintain water resistance.

  4. Please note that the device cannot be powered off using the button on the top. This button has two primary functions:

    • Short press: Pressing the button briefly allows you to view the battery level or charging progress when the device is connected to a power source.

    • Long press: Holding down the button wakes up the device from sleep mode. When awakened, the device should report its status. However, please note that this button does not function as an SOS button, and no SOS alert will be generated.

ASSET 422

Powering Off:

  1. Locate the four screws on the back of the tracker. Use a screwdriver to unscrew these four screws to remove the faceplate of the device.

  2. After removing the faceplate, you will see a power switch. Flip the power switch to the OFF position. This will turn off the tracker.

  3. Make sure the power switch is securely set to the OFF position before proceeding.

Powering On:

  1. When you're ready to turn the tracker back on, flip the power switch to the ON position.

  2. Click the button briefly to verify if the tracker is on. If the tracker is powered on, you will see the lights illuminate solidly while holding the button at any time. The lights indicate that the tracker is functioning.

  3. Do not hold the button down for an extended period (3 seconds) as it may cause the tracker to turn on or off. Briefly hold the button to check for the appearance of lights, confirming that the tracker is on.

By following these steps, you can successfully power-cycle the Asset 422 tracker. If you have any further questions or encounter any difficulties, please feel free to reach out for assistance.

ASSET 432

Powering On:

  1. Open the device to access the internals.

  2. Locate the on/off switch inside the device and ensure it is switched to the "ON" position.

  3. Once the switch is set to "ON," find the button located above the switch.

  4. Press and hold the button for approximately 2 seconds or until you see lights indicating that the tracker is powering on.

  5. Release the button after seeing the lights. Do not press the button again.

Powering Off:

  1. Open the device again to access the internals.

  2. Locate the on/off switch inside the device and flip it to the "OFF" position.

  3. The tracker is now powered off and will cease its operations.

Powering On Again:

  1. If you want to power on the tracker again, open the device and ensure the on/off switch is in the "ON" position.

  2. You do not need to press the button again. The tracker should automatically resume normal reporting and wake up at the time it was last rebooted. By following these steps, you can effectively power-cycle the Asset 432 tracker.


If you require further assistance or encounter any issues beyond what is covered in this article, our dedicated support team is ready to assist you. Feel free to visit our Support Center at https://logistimatics.com/contact/ or contact us at hello@logistimatics.com for personalized guidance and prompt resolution of any concerns you may have.

You can also find helpful video tutorials and FAQs on our website to further enhance your experience. Thank you for choosing Logistimatics, and we wish you a seamless tracking experience!

Did this answer your question?